Lift Roles ReferenceMinimum US training, qualification & evaluation requirements for crane and rigging roles

For reference only · Status as of 15 Nov 2026. Federal OSHA rules apply only where their stated scope and conditions are met. ANSI/ASME standards are not automatically law; they may apply through adoption, contract, or other obligations. Industry practices are guidance, not automatically mandatory. Verify jurisdiction, equipment, manufacturer instructions, and current primary sources. This educational site does not qualify personnel or approve lifts.

How to read this resource: Federal OSHA rule = binding only when applicable to the work; ANSI/ASME consensus standard = not automatically binding unless adopted or otherwise required; Recommended practice = guidance, not automatically a legal duty. Check state/local rules, contract provisions and manufacturer instructions.

Who does what on a crane lift

Minimum qualification, training and expectations for crane and rigging roles, based on OSHA, ASME and ANSI. Free resources for the whole industry.

Find your roleGet the free awareness modules
A barricaded crawler crane lifting a load to its set point while a telescopic boom forklift carries a pallet on its forks, with the eight lift roles marked and the crew standing clear of both loads. Select a role to open its page.LHE UserCrane OperatorA/D DirectorQualified RiggerOperator EvaluatorLift DirectorSignal PersonLift Crew Member
Select a role on the lift to see what OSHA and ASME expect.

What you'll find here

Everything is free. Use it as a reference, print it for the field or add it to your own program.
Not sure where to start?Safety or supervision → RolesTraining manager → Awareness modulesPlanning a lift → Lift helperHave a question → Common questions

The lift roles

Select a role for its requirements, awareness module and print checklist

Rigging gear

Inspection and removal criteria, and the person who signs off on them

Planning a lift? Answer a few questions and see which roles, records and briefings federal OSHA expects.

Open the lift helper

What's changing

All changes
16 Nov 2026
New: Pre-Mobilization Training Checklist (Form 8, Rev 0)

A per-worker self-assessment for any employer: confirm that required training, testing, evaluation and records are complete for each assigned role before the worker mobilizes. Word and print-ready PDF. Download the forms

16 Nov 2026
Training modules are now awareness modules

The eight modules cover what the standards require for each role and for the employer. They do not train, test or qualify anyone, and the written exams are now awareness checks. Audience: managers, training coordinators, supervisors and evaluators who run or verify a crane and rigging training and qualification program. Slides, checks, answer keys, scoring sheets and instructor packages have new revisions. Download the modules

16 Nov 2026
New: Rigging and lifting role and authorization matrix (Rev 0)

One table shows which roles may do which lift tasks, from the fall zone to directing the lift, with the controlling condition, citation and source type for each row. Excel and printable PDF downloads. Open the role matrix

Rigging Hardware Inspector

People who inspect slings, rigging hardware, below-the-hook devices and hoists, and take damaged gear out of service.

OSHA minimum qualification / evaluation

Daily inspection of slings and their fastenings and attachments by a competent person designated by the employer (1926.251(a)(6); 1910.184(d)). OSHA sets no exam, card or course. The employer designates the person and should be able to show the basis.

Training

No OSHA training rule written for the inspector. The person must know the gear and its removal criteria well enough to act as the employer's designated competent person. ASME B30 volumes call for training of the people who inspect and use the equipment.

Who may evaluate

Employer (designation).

Records OSHA requires

Alloy steel chain slings: the month of the most recent thorough periodic inspection (1926.251(b)(6)(ii); 1910.184(e)(3)(ii)). Hooks with no manufacturer rating: dates and results of the 2x load test (1926.251(f)(2)). Other inspection records come from the ASME volumes and the manufacturer.

Retraining / re-evaluation

Event-driven: missed defects, an incident, or new types of gear on the job.

Portability

Not portable. Each employer designates its own inspectors.

ASME / ANSI adds

B30.9 (slings), B30.26 (rigging hardware), B30.10 (hooks), B30.20 (below-the-hook devices), B30.16/B30.21 (hoists) and B30.23 (personnel lifting): initial, frequent and periodic inspections, periodic ones by a designated person, written removal criteria, and periodic inspection records for some equipment.

Key citations: 1926.251(a)(1),(a)(6),(b)(6),(f)(2); 1910.184(d),(e)(3); 1926.1431(j)

Responsibilities: requirements and field practice

Two complementary lenses. Check the actual work and equipment before deciding what applies.

Applicable obligations · verify scope

Regulatory and standards requirements

Determine which equipment is being inspected and the applicable OSHA, manufacturer, and adopted-standard criteria. Do not treat all slings, hooks and hardware as having identical inspection rules.

Starting references: OSHA construction: 29 CFR 1926.251; equipment-specific criteria apply. ASME provisions are not automatically law; confirm edition, adoption and contractual applicability.

Recommended · not automatically mandatory

Practical responsibilities and recommended practices

Check identification and service condition; document defects, remove questionable items from service, and direct unresolved suitability decisions to a competent or qualified person as applicable.

Independent educational guidance; employer procedures and job-specific lift planning control implementation.

Trial guidance, not authorization or a compliance determination. Existing role requirements below remain under citation review.

Downloads for this role

Specific to this role 16

Qualification
Inspection sections (each volume)Consensus “shall”Verify

Inspections are grouped as initial (before first use), frequent (each day or shift the gear is used, by the user or another designated person) and periodic (a complete inspection by a designated person, at an interval based on service).

Source: ASME B30.9 / B30.26 / B30.10Keep: Designated person list; periodic inspection record where the volume requires oneWhen: Initial; each shift; periodicApplies: All industries (consensus)
Paraphrased. Typical periodic intervals: normal service yearly, severe service monthly to quarterly, special service as a qualified person recommends.
Designation

Each day before use, a competent person designated by the employer inspects slings and all fastenings and attachments. Damaged or defective slings are removed from service immediately.

Source: OSHA 29 CFR 1926.251Keep: Inspector designation list; tag or removal recordWhen: Daily before useApplies: Construction (29 CFR 1926)
This is the rule that creates the inspector role in construction. OSHA does not say how the person is trained or tested.
1910.184(d)OSHA law

General industry: slings and their fastenings and attachments are inspected each day before use by a competent person designated by the employer; damaged or defective slings are removed from service.

Source: OSHA 29 CFR 1910.184Keep: Inspector designation listWhen: Daily before useApplies: General industry (29 CFR 1910)
Training
Inspector competencyIndustry practice

Employers commonly qualify inspectors through classroom training on each type of gear and its removal criteria, supervised inspections, and a documented competency check before designation, with refreshers when gear or procedures change.

Source: Employer programKeep: Training + competency record; designationWhen: Before designation; refresher per programApplies: All industries (voluntary)
Good practice, not a federal rule. Awareness modules on this site do not train or qualify anyone.
Documentation

Alloy steel chain slings get a thorough periodic inspection at an interval set by frequency of use, severity of service, the nature of the lifts and service-life experience, and never more than 12 months apart. The employer keeps a record of the most recent month each chain sling was thoroughly inspected.

Source: OSHA 29 CFR 1926.251Keep: Periodic inspection record (month) per chain slingWhen: At least every 12 monthsApplies: Construction (29 CFR 1926)
The only fixed sling inspection interval in federal OSHA.

General industry: alloy steel chain slings in use get a thorough inspection at least once every 12 months, with a record of the most recent month inspected.

Source: OSHA 29 CFR 1910.184Keep: Periodic inspection record (month) per chain slingWhen: At least every 12 monthsApplies: General industry (29 CFR 1910)

Hook ratings follow the manufacturer's recommendations. A hook with no manufacturer recommendation is tested to twice its intended safe working load before first use, and the employer keeps a record of the test dates and results.

Source: OSHA 29 CFR 1926.251Keep: Hook test recordWhen: Before first useApplies: Construction (29 CFR 1926)
Inspection records (each sling chapter)Consensus “shall”Verify

A written record of the most recent periodic inspection is kept for slings.

Source: ASME B30.9-2025 SlingsKeep: Periodic inspection record per sling (or per lot/ID)When: Each periodic inspectionApplies: All industries (consensus)
Confirm which sling types and what the record must show in the licensed copy.
Periodic inspectionConsensus “shall”Verify

Below-the-hook devices get frequent and periodic inspections at intervals set by service class, with dated records of periodic inspections. A device that has been altered, repaired or modified is load tested by or under a qualified person before return to service, at no more than 125% of rated load unless the manufacturer says otherwise.

Source: ASME B30.20-2025 Below-the-Hook Lifting DevicesKeep: Dated periodic inspection record; load test recordWhen: Per service class; after repairApplies: All industries (consensus)
Responsibility

Rigging equipment is inspected before use on each shift and as needed during use. Defective rigging equipment is removed from service.

Source: OSHA 29 CFR 1926.251Keep: Inspection practice / tag-out of rejected gearWhen: Each shift; during useApplies: Construction (29 CFR 1926)
1926.251(a)(4)OSHA lawVerify

Custom-designed grabs, hooks, clamps and other lifting accessories for items such as modular panels and prefabricated structures are marked with their safe working load and proof tested to 125% of rated load before use.

Source: OSHA 29 CFR 1926.251Keep: Marking + proof test recordWhen: Before first useApplies: Construction (29 CFR 1926)
Confirm the paragraph number on osha.gov.
1926.251(c)(4)(iv)OSHA lawVerify

Wire rope is removed from use if, in any length of eight diameters, visible broken wires exceed 10% of the total wires, or the rope shows other signs of excessive wear, corrosion or defect.

Source: OSHA 29 CFR 1926.251Keep: Removal record / tagWhen: Each inspectionApplies: Construction (29 CFR 1926)
ASME B30.9 uses a different broken-wire count for slings. Apply whichever your procedure adopts, and never the less strict of the two.
1926.251(e)(8)OSHA lawVerify

Synthetic web slings are removed from service for acid or caustic burns, melting or charring, snags, punctures, tears or cuts, broken or worn stitches, or distorted fittings.

Source: OSHA 29 CFR 1926.251Keep: Removal record / tagWhen: Each inspectionApplies: Construction (29 CFR 1926)
1926.1431(j)OSHA lawVerify

Crane-suspended personnel platforms and their rigging are proof tested to 125% of the platform's rated capacity at each jobsite before hoisting employees, and after any repair or modification.

Source: OSHA 29 CFR 1926.1431Keep: Proof test recordWhen: Each jobsite; after repairApplies: Construction (29 CFR 1926)
See also the trial lift and inspection provisions of 1926.1431 and ASME B30.23.
Inspection sectionsConsensus “shall”Verify

Hand chain and lever hoists get frequent inspections (hook, load chain, brake and controls) and periodic inspections by a designated person, with removal criteria for the load chain, hook and brake.

Source: ASME B30.16 / B30.21Keep: Periodic inspection recordWhen: Frequent; periodic per serviceApplies: All industries (consensus)
Hooks on hoists also follow B30.10.
Color-code programsIndustry practice

Many sites mark the latest periodic inspection with a color code by month or quarter, often with a second mark for the year. OSHA and ASME do not require color codes. They require the inspection, and records where noted.

Source: Employer programKeep: Posted color scheme + inspection recordsWhen: Per programApplies: All industries (voluntary)
A color tag shows the gear was inspected. It does not replace a required written record.
Applies to everyone on the lift 5 general requirements, including this role

Employer must instruct each employee in recognizing and avoiding unsafe conditions and the regulations applicable to their work environment.

Source: OSHA 29 CFR 1926.21Keep: Training roster / toolbox or orientation recordWhen: Initial; as conditions changeApplies: Construction (29 CFR 1926)
Baseline for every person on a lift team.

Employer must evaluate each employee required to be trained under Subpart CC to confirm the employee understands the information provided in the training.

Source: OSHA 29 CFR 1926 Subpart CCKeep: Evaluation record (quiz, demonstration, sign-off)When: After each required trainingApplies: Construction (29 CFR 1926)
Applies to every Subpart CC training requirement - a sign-in sheet alone does not show understanding.

Refresher training is required when an employee's conduct or an evaluation indicates retraining is necessary.

Source: OSHA 29 CFR 1926 Subpart CCKeep: Retraining record + trigger (incident, observation)When: Event-driven (no fixed interval in OSHA)Applies: Construction (29 CFR 1926)
OSHA sets no calendar refresher for most crane roles; employers should set one in their own procedures.

Training required by Subpart CC must be provided at no cost to the employee.

Source: OSHA 29 CFR 1926 Subpart CCKeep: Cost policyWhen: OngoingApplies: Construction (29 CFR 1926)
Personnel competence (each B30 volume)Consensus “shall”Verify

Persons performing functions identified in the volume must meet its qualifying criteria and be trained in and familiar with the volume, through education, training, experience, skill and physical fitness as necessary.

Source: ASME B30 series (all volumes)Keep: Qualification file per personWhen: Initial; maintainApplies: All industries (consensus)
Paraphrased; confirm wording in the licensed copy of each volume you rely on.

Lift helper

Select the conditions that describe the work. The results flag potential federal OSHA roles, records and briefings for further verification, with citations. They are not a compliance determination, engineered lift plan, authorization to proceed, or personnel qualification. Confirm scope, current regulations, manufacturer instructions, site procedures and any state or contractual requirements before work.

The work

The lift

Other equipment

Where

Everyone on the job Role requirements

  • Instruction in recognizing and avoiding unsafe conditions for their work. 1926.21(b)(2)
  • Crane-area training: swing and crush zones, holes, crush and pinch points. 1926.1430(e); 1926.1424
  • The employer confirms each person understood the training; a sign-in sheet alone is not enough. 1926.1430(g)(1)
  • Required training is provided at no cost to employees. 1926.1430(g)(3)
  • Anyone who sees a safety problem may give the stop or emergency stop signal, and the operator must obey it. 1926.1419(j); 1926.1417(y)

Crane operator Role requirements

  • Certified or licensed for the equipment type (valid up to 5 years), at no cost to the employee. 1926.1427(c)–(e); 1926.1427(c)(3)
  • Employer evaluation on this equipment and the assigned work, documented and available at the site. 1926.1427(f)

Rigging hardware inspection Role requirements

  • Rigging is inspected before use each shift, and slings and their fittings daily by a competent person the employer designates. 1926.251(a)(1); 1926.251(a)(6)
  • Alloy chain slings: a thorough inspection at least every 12 months, with the month recorded. 1926.251(b)(6)
  • Removal criteria by item: Rigging hardware.

This list is a reference aid based on federal OSHA and the cited standards. It is not a lift plan, does not cover every rule, and does not qualify anyone.

Rigging hardware

Inspection types and common removal criteria for rigging gear, with the OSHA rule and ASME volume for each. ASME criteria are paraphrased and some are approximate. The manufacturer's instructions and the current standard control, and they can be stricter than what is listed here.

Reference only. Removal criteria are summarized, not complete. Follow the manufacturer's instructions and the current ASME edition, and remove any gear you are unsure about until a designated person has inspected it. See the Rigging Hardware Inspector role, or download Form 6, the rigging gear inspection checklist.

Inspection types

InspectionWhoWhenRecordsBasis
InitialDesignated personBefore first use of new, repaired, altered or modified gearPer volume; many employers record it with the first periodic inspectionASME B30.9, B30.26, B30.10, B30.20
Frequent (before use)The user or another designated personEach day or shift the gear is used, and as needed during useNo written record required; tag and remove rejected gear1926.251(a)(1), (a)(6); 1910.184(d); ASME B30 volumes
PeriodicDesignated personInterval set by service: normal service yearly, severe service monthly to quarterly, special service as a qualified person recommendsAlloy chain slings: month of last inspection (OSHA). Slings and below-the-hook devices: periodic records (ASME)1926.251(b)(6); 1910.184(e)(3); ASME B30.9, B30.20
After an incident or repairDesignated or qualified personAfter an overload, shock load, heat exposure, damage or repairInspection or load test record before return to serviceASME B30.20 (load test); manufacturer

Slings

Wire rope slingsVerify

ASME: ASME B30.9 (wire rope slings chapter)
OSHA: 1926.251(c); 1910.184(f)

Marking

Manufacturer name or trademark, rated loads for the hitches used, diameter or size, and number of legs if more than one.

Remove from service if

  • Missing or unreadable tag
  • Broken wires over the limit: OSHA uses 10% of the wires in any length of eight diameters; ASME B30.9 uses a count per rope lay
  • Kinking, crushing, birdcaging or other distortion
  • Severe localized abrasion, scraping or corrosion
  • Heat damage
  • End fittings cracked, deformed or worn, or showing pulled or slipped rope

OSHA and ASME broken-wire tests differ. Write one test into your procedure and never use the less strict.

Alloy steel chain slingsVerify

ASME: ASME B30.9 (alloy steel chain slings chapter)
OSHA: 1926.251(b); 1910.184(e)

Marking

Permanently affixed durable tag stating size, grade, rated capacity and reach.

Remove from service if

  • Missing or unreadable tag
  • Cracks or breaks
  • Wear, nicks or gouges beyond the manufacturer's limits (OSHA Table H-2 gives maximum link wear)
  • Stretched, bent, twisted or deformed links or fittings
  • Heat damage, weld spatter or arc strikes
  • Links that don't hinge freely

OSHA sets the only fixed sling interval here: a thorough inspection at least every 12 months, with the month recorded. Use only alloy chain graded for overhead lifting.

Synthetic web slingsVerify

ASME: ASME B30.9 (synthetic webbing slings chapter); WSTDA WS-1
OSHA: 1926.251(e); 1910.184(i)

Marking

Manufacturer name or trademark, rated capacities for each hitch, type of material, and a code or stock number.

Remove from service if

  • Missing or unreadable tag
  • Acid or caustic burns
  • Melting, charring or weld spatter
  • Holes, tears, cuts or snags
  • Broken or worn stitching in load-bearing splices
  • Excessive abrasion, knots, or exposed red warning yarns
  • Discolored, brittle or stiff areas
  • Fittings pitted, corroded, cracked, bent or distorted

Protect slings from sharp edges with suitable softeners. A piece of cardboard or a rag is not edge protection.

Synthetic roundslingsVerify

ASME: ASME B30.9 (synthetic roundslings chapter); WSTDA RS-1
OSHA: 1926.251(a) general rigging rules

Marking

Manufacturer name or trademark, rated loads for each hitch, core and cover material, and a code or stock number.

Remove from service if

  • Missing or unreadable tag
  • Acid or caustic burns, melting or charring
  • Holes, tears, cuts, abrasion or snags that expose the core yarns
  • Broken or damaged core yarns (feel along the full length for lumps, voids or hard spots)
  • Weld spatter, knots, or discolored, brittle or stiff areas
  • Damaged fittings

Hardware that bears on a roundsling must have the diameter and shape the manufacturer requires, or the sling's rating drops.

Synthetic rope slings (including HMPE)Verify

ASME: ASME B30.9 (synthetic rope slings chapter)
OSHA: 1926.251(d); 1910.184(h)

Marking

Manufacturer name or trademark, rated loads for each hitch, rope material and size.

Remove from service if

  • Missing or unreadable tag
  • Cuts, gouges or areas of broken fibers
  • Melting, charring or heat damage
  • Abrasion or wear beyond the manufacturer's limits
  • Changes in diameter, stiffness or flexibility
  • Damaged splices or fittings

High-performance fibers such as HMPE have their own inspection criteria. Use the manufacturer's inspection guide for these.

Hardware

ShacklesVerify

ASME: ASME B30.26 (shackles chapter)
OSHA: 1926.251(f)(1) and Table H-19

Marking

Manufacturer name or trademark, rated load and size.

Remove from service if

  • Missing or unreadable marking
  • Heat damage, weld spatter or arc strikes
  • Excessive pitting or corrosion
  • Bent, twisted, stretched, elongated, cracked or broken body or pin
  • Excessive nicks or gouges
  • 10% reduction of the original or catalog dimension at any point on the body or pin
  • Pin not fully engaged, or damaged threads
  • Signs of unauthorized welding

Replace pins only with the manufacturer's pin. Side loading reduces the rating; use the manufacturer's reduction.

HooksVerify

ASME: ASME B30.10
OSHA: 1926.251(f)(2)

Marking

Manufacturer identification; rated load where the volume requires it.

Remove from service if

  • Missing or unreadable identification
  • Cracks, nicks or gouges
  • Wear over 10% of the original section dimension
  • Throat opening grown beyond the limit (commonly 5%, or per the manufacturer)
  • Twist of more than 10 degrees from the plane of the unbent hook
  • Latch missing, damaged or not closing where a latch is required
  • Heat damage, or any repair or welding the manufacturer did not approve

Many manufacturers mark throat-gauge points on the hook. Measure against them and record the baseline when the hook is new.

Eyebolts and swivel hoist ringsVerify

ASME: ASME B30.26
OSHA: 1926.251(a)

Marking

Manufacturer name or trademark, size or rated load, and torque value for swivel hoist rings.

Remove from service if

  • Missing or unreadable marking
  • Bent, elongated or cracked shank or eye
  • Damaged threads, or nicks and gouges
  • Heat damage or corrosion
  • Swivel hoist ring that doesn't pivot and turn freely, or a loose bolt

Only shoulder eyebolts are rated for angled loads, at a reduced rating from the manufacturer. Install swivel hoist rings to the manufacturer's torque and thread engagement.

Turnbuckles, wire rope clips and wedge socketsVerify

ASME: ASME B30.26 (adjustable and compression hardware chapters)
OSHA: 1926.251(c)

Marking

Manufacturer name or trademark and size; rated load for turnbuckles.

Remove from service if

  • Missing or unreadable marking
  • Bent, cracked or distorted
  • Damaged or worn threads
  • Heat damage or corrosion
  • Clips or sockets that won't hold torque, or show slippage

Lock turnbuckles against turning. Install wire rope clips per the manufacturer (saddle on the live end, correct number and torque) and re-torque after the first load.

Below-the-hook

Spreader bars, lifting beams and framesVerify

ASME: ASME B30.20; design per ASME BTH-1
OSHA: 1926.251(a)(4) (custom lifting accessories)

Marking

Rated load, manufacturer name and contact, serial number, device weight if over 100 lb, and design category and service class for devices built to BTH-1.

Remove from service if

  • Missing or unreadable rated load or ID
  • Bent, cracked or deformed structural members
  • Cracked welds
  • Damaged, worn or deformed lifting lugs, pins or holes
  • Loose or missing bolts, pins, keepers or guards
  • Any repair or modification without engineering approval and a load test

A device built in the field or modified needs engineering, marking and a load test before use. Use only the configuration shown on the drawing or nameplate.

Plate clamps and beam clampsVerify

ASME: ASME B30.20 (mechanical lifters); manufacturer's manual
OSHA: 1926.251(a)

Marking

Manufacturer, model, rated load and serial number; plate thickness range for plate clamps.

Remove from service if

  • Missing or unreadable rated load or ID
  • Cracked or deformed body or jaw
  • Worn, chipped or loaded-up gripping teeth, cams or pads
  • Weak or broken springs, or a lock that won't hold closed
  • Loose or worn pins, bolts or lifting shackle
  • Past the manufacturer's overhaul or proof-test date

Use a plate clamp only in the direction it is rated for (vertical, horizontal or turning), within its thickness and hardness range, and one plate at a time. Read the manual for side-pull limits.

Lifting magnets and vacuum liftersVerify

ASME: ASME B30.20 (magnet and vacuum lifter chapters)
OSHA: 1926.251(a)

Marking

Rated load, manufacturer, serial number and weight; power and control data for powered lifters.

Remove from service if

  • Damaged or uneven lifting face or seal
  • Indicators, alarms or controls not working
  • Backup power or battery warning not working
  • Cracked housing, damaged cable or lifting lug
  • Failed the manufacturer's breakaway or holding test

Rated load depends on the material, thickness, surface and flatness of the load. Check the manufacturer's derating chart for each lift.

Hoists

Chain hoists and lever hoistsVerify

ASME: ASME B30.16 (hand chain hoists); B30.21 (lever hoists); hooks per B30.10
OSHA: 1926.554 (overhead hoists)

Marking

Manufacturer, model, serial number and rated load.

Remove from service if

  • Load chain stretched or worn beyond the manufacturer's gauge, or twisted, nicked or gouged
  • Hook defects (see Hooks)
  • Brake slipping or not holding
  • Missing or damaged chain stop or tail pin
  • Cracked or distorted housing or frame
  • Lever, pawl or selector not working correctly

Never extend a lever handle or use more than one person to pull a hand chain. A hoist that needs that much force is overloaded.

Personnel lifting

Crane-suspended personnel platformsVerify

ASME: ASME B30.23
OSHA: 1926.1431

Marking

Platform weight and rated load capacity, with platform identification.

Remove from service if

  • Structural damage, cracked welds or missing parts
  • Damaged guardrails, gates or toe boards
  • Rigging or hardware defects (see the items above)
  • Failed proof test or trial lift inspection

Proof test the platform and rigging to 125% of rated capacity at each jobsite and after any repair. Rigging used for personnel hoisting is reserved for that purpose.

Questions

Short answers to the questions crews, supervisors and contractors ask most. Each answer cites its clause. Open a question to see the answer; use “Copy link” to share one.

66 of 66 questions
Crane Operator

Is an NCCCO (or other accredited) operator card enough by itself to let someone run our crane?

No. OSHA requires BOTH certification (or a qualifying license) AND a separate employer evaluation.

Certification proves general knowledge for a crane type. The employer must also evaluate the operator on the equipment and tasks they will be assigned, including safety devices and configuration. A certificate or degree alone does not meet the evaluation requirement.

OSHA law29 CFR 1926.1427(a), (f)
Crane Operator

What must the operator evaluation record include, and where must it be kept?

Operator name, evaluator name and signature, date, and the make, model and configuration of the equipment. It must be available at the worksite.

Keep it at the site for as long as the operator works for the employer. Where electronic records are not available, keep a paper copy in the site crane file.

OSHA law29 CFR 1926.1427(f)
Crane Operator

How long is an operator certification valid?

Up to 5 years. A state license is valid for the period the state stipulates, but no more than 5 years.

Track expiration dates and plan recertification before the card lapses. An expired certification means the person may only operate as an operator-in-training.

OSHA law29 CFR 1926.1427(c)-(e)
Crane Operator

Is an operator's certification or evaluation portable when they change employers?

The accredited certification is portable. The employer evaluation is not: the new employer must do its own evaluation.

Certification from an accredited testing organization travels with the operator. Certification from another company's audited employer program does not. In every case the new employer must evaluate the operator before they run its equipment.

OSHA law29 CFR 1926.1427(d), (e), (f)
Crane Operator

If an operator was evaluated on one crane, do they need a new evaluation for a different crane?

Only if the new crane requires substantially different skills, knowledge or configuration.

After a successful evaluation, an operator may run other equipment the employer determines does not need substantially different skills. A move from a small RT to a large lattice crawler, a tower crane, or a new configuration such as luffing jib or superlift usually needs a new evaluation. Document the decision either way.

OSHA law29 CFR 1926.1427(f)
Crane Operator

Can an uncertified person run a crane while they are in training?

Yes, only as an operator-in-training: continuously monitored by a qualified trainer, with tasks within their ability.

Training must combine formal and practical instruction. The trainer must keep line of sight and communication (direct communication for tower cranes), and may take only short breaks under set conditions. See the next question for what trainees may not do.

OSHA law29 CFR 1926.1427(b)
Crane Operator

What is an operator-in-training NOT allowed to do?

No work near power lines (within 20 ft up to 350 kV or 50 ft above), no personnel hoisting, no multi-crane lifts, no lifts over shafts, cofferdams or tank farms.

Multiple-lift rigging is also restricted unless the trainer decides the trainee's skills are sufficient.

OSHA law29 CFR 1926.1427(b)(3)
Crane Operator

When must an operator be retrained or re-evaluated?

When their performance or an evaluation shows they need it. After retraining they must be re-evaluated.

Typical triggers are an incident, a near miss, an observed unsafe act, or a failed field observation. Record the trigger, the retraining and the re-evaluation.

OSHA law29 CFR 1926.1427(b)(5), (f)
Crane Operator

Is there a required refresher interval for crane operators?

OSHA sets no fixed refresher interval. Retraining is event-driven, and certification must be renewed within 5 years.

Because OSHA has no calendar requirement, the refresher interval is an employer program decision and should be stated in the procedure.

OSHA law29 CFR 1926.1430(g)(2); 1926.1427
Crane Operator

Can operator tests be given verbally or in Spanish?

Yes. They can be oral (after a written literacy check) and in any language the candidate understands.

The certificate must note the language. The operator may then only run equipment furnished with materials, such as load charts and manuals, in that language.

OSHA law29 CFR 1926.1427(h)
Crane Operator

Besides certification, what training must operators receive?

Safe operation of their equipment, power-line safety, emergency procedures, tag-out and start-up, and work-area/crush-point hazards.

Friction-crane operators must also be trained to raise the boom a short distance before swinging it off a support. Every training must be followed by an evaluation of understanding.

OSHA law29 CFR 1926.1430(a), (c), (e), (f), (g)
Crane Operator

Do overhead or gantry crane operators in a shop or fabrication facility need OSHA certification?

No. In general industry OSHA only requires that operators be designated. ASME B30.2 and B30.17 cover their training and qualification.

For consistency, apply a qualification process for shop cranes based on the ASME operator training chapter.

OSHA + ASME29 CFR 1910.179(b)(8); ASME B30.2 / B30.17
Crane Operator

Do derricks, side booms and small cranes (2,000 lb or less) fall under the operator certification rule?

No. They are excluded from 1926.1427 and have their own sections: derricks 1436, side booms 1440, 2,000 lb or less 1441.

Side-boom operators must still be trained in safe operation under 1926.1430(c).

OSHA law29 CFR 1926.1427(a)(2)
Crane Operator

Does ASME require physical or medical criteria for operators?

ASME B30.5 includes physical criteria such as vision, hearing, depth perception and seizure history, plus substance-use provisions. Some are 'shall' and some are 'should'.

OSHA has no equivalent in Subpart CC. Check the licensed B30.5 copy before writing these into a procedure, and keep medical records separate from training files.

Consensus standardASME B30.5, 5-3.1.2 (verify)
Qualified Rigger

Does OSHA require riggers to be certified?

No. OSHA requires a 'qualified rigger' for certain work. That means a rigger who meets the qualified-person criteria, as determined by the employer.

Qualified person means a recognized degree, certificate or professional standing, or extensive knowledge, training and experience, plus demonstrated ability to solve problems related to the work. OSHA does not prescribe a test, but the employer must be able to show how it made the determination.

OSHA law29 CFR 1926.1401
Qualified Rigger

When does OSHA require a qualified rigger?

Two cases: workers in the fall zone hooking, unhooking or guiding the load, and all rigging during crane assembly/disassembly.

Steel erection has its own rigging provisions, including training for multiple-lift rigging.

OSHA law29 CFR 1926.1425(c)(3); 1926.1404(r)(1)
Qualified Rigger

Does ASME require a qualified rigger on every mobile crane job?

Yes. Since B30.5-2021, at least one qualified rigger is required wherever a mobile crane is used, in any industry.

The employer designates the rigger as qualified based on evidence of passing a written AND practical exam covering the B30.5 competency areas.

Consensus standardASME B30.5-2021, 5-3.1 (verify clause)
Qualified Rigger

What must a rigger qualification exam cover under ASME B30.5?

Selection and use of rigging hardware; standard hitches; estimating load weight, center of gravity, sling angles/loading and load movement; and rigging inspection.

Both a written and a practical exam are required. CCO Rigger II is commonly cited as meeting these areas. An employer's in-house exam can meet them if mapped to all four.

Consensus standardASME B30.5-2021; ANSI/ASSP A10.42
Qualified Rigger

Can an employer give its own rigger qualification exam instead of using a third party?

Yes. Qualification is an employer designation, and the exam may be administered by anyone as long as it covers the required competencies.

Keep the exam results and the designation in the person's file. Owner contracts sometimes require third-party certification, so check the project spec.

OSHA + ASME29 CFR 1926.1401; ASME B30.5
Qualified Rigger

Who must inspect rigging before use, and how often?

In construction, rigging equipment is inspected before use on each shift and as needed during use, and a competent person designated by the employer inspects slings and their fastenings each day before use. In general industry, a competent person inspects slings each day before use.

Also follow the B30.9 (slings) and B30.26 (hardware) inspection and removal criteria.

OSHA law29 CFR 1926.251(a)(1), (a)(6); 1910.184(d)
Qualified Rigger

Do sling and rigging hardware users need training?

Yes, under ASME: users must be trained in selection, inspection, cautions to personnel, environmental effects and rigging practices.

This applies to anyone who uses slings or hardware, not only designated qualified riggers.

Consensus standardASME B30.9-2025; B30.26-2026
Qualified Rigger

Is special training needed for multiple-lift rigging (Christmas-treeing) in steel erection?

Yes. Employees who do multiple-lift rigging must receive specific training on that procedure.

OSHA law29 CFR 1926.761(c)(1)
Signal Person

Can an employer qualify signal persons in-house?

Yes, through an employer's qualified evaluator. That qualification is not portable to other employers.

The evaluator must be an employee of the employer who has shown they can accurately assess signal persons against 1926.1428. The alternative is a third-party qualified evaluator, whose documentation is portable.

OSHA law29 CFR 1926.1428(a); 1926.1401
Signal Person

What testing does a signal person need?

An oral or written test AND a practical test.

The tests must show knowledge and use of the signal types used (Standard Method hand signals where applicable), basic crane operation and limits including load dynamics and boom deflection, and the signaling rules in 1926.1419-.1422 and .1428.

OSHA law29 CFR 1926.1428(c)
Signal Person

What signal person documentation must be on site?

Proof of qualification, available at the site while the person works for the employer, listing each type of signaling they are qualified for.

A person qualified only for radio/voice signals may not give hand signals unless that type is also documented.

OSHA law29 CFR 1926.1428(a)(3)
Signal Person

When is a signal person required?

When the operator can't see the load, landing area or path; when traveling with view obstructed; or when the operator or person handling the load decides one is needed.

Non-standard hand signals and voice signals must be agreed in advance by the operator, signal person and lift director (if there is one). Standard Method hand signals need no pre-agreement.

OSHA law29 CFR 1926.1419(a), (c)(2); 1926.1421(a)
Signal Person

What happens if a signal person shows they don't know the signals?

Stop them from signaling until they are retrained and reassessed.

Document the removal, retraining and new assessment.

OSHA law29 CFR 1926.1428(b)
Signal Person

Do dedicated spotters for power-line work need to be qualified?

Yes. A dedicated spotter must meet the signal-person qualification requirements.

Treat power-line spotters as signal persons for qualification and documentation.

OSHA law29 CFR 1926.1401 (definition); 1926.1428
Signal Person

What are the signal person requirements at a plant (general industry)?

OSHA 1910 has no signal-person qualification rule. Use ASME B30 and apply the 1926.1428 process for consistency.

Consensus standardASME B30.5 / B30.2
Lift Crew

What training do tag-line handlers, helpers and other crew in the crane work area need?

Hazard recognition, crush/pinch-point and swing-radius hazards, and power-line hazards when working near lines, followed by a check of understanding.

Add tag-out training for anyone authorized to start or energize equipment, and briefings for A/D, multi-crane and personnel-hoisting work.

OSHA law29 CFR 1926.21(b)(2); 1926.1430(a), (e), (f), (g)
Lift Crew

Is a training sign-in sheet enough to show compliance?

No. The employer must evaluate each trained employee to confirm they understood the training.

Use a short quiz, a practical demonstration, or a supervisor sign-off that records the result.

OSHA law29 CFR 1926.1430(g)(1)
Lift Crew

Who is allowed in the fall zone?

Only employees needed to hook, unhook or guide the load, or to receive it, and never directly under the load except as the tilt-up/down rules allow.

If people are in the fall zone hooking, unhooking or guiding, the load must be rigged by a qualified rigger and use latched hooks.

OSHA law29 CFR 1926.1425
Lift Crew

Who must attend the pre-lift meeting for hoisting personnel?

The operator, the signal person (if needed), the employees to be hoisted, and the person responsible for the task.

Hold it before the trial lift at each new work location, and again for any employee newly assigned to the operation.

OSHA law29 CFR 1926.1431(m)
Lift Crew

Is a meeting required before a multiple-crane lift?

Yes. The lift director must review the plan in a meeting with all workers who will be involved.

OSHA law29 CFR 1926.1432(b)(2)
Lift Crew

Can an employer charge employees for required crane training?

No. Training required by Subpart CC must be provided at no cost to the employee, and so must operator certification.

OSHA law29 CFR 1926.1430(g)(3); 1926.1427(c)(3)
Load Handling Equipment

What training is required for chain fall and lever hoist users?

OSHA requires only general hazard instruction. ASME B30.16 and B30.21 require operators to be trained.

B30.21-2025 (effective 10-Feb-2026) adds that a means of communication must be set up before operating when signals are needed.

OSHA + ASME29 CFR 1926.21(b)(2); ASME B30.16 / B30.21
Load Handling Equipment

What training is required for jacks, rollers, air casters or hydraulic gantries?

OSHA requires only general hazard instruction. ASME B30.1 covers operator training and competence.

Consensus standardASME B30.1-2026
Load Handling Equipment

What do forklift or telehandler operators need?

Formal and practical training, a workplace evaluation before operating, an evaluation at least every 3 years, and an employer certification record.

Refresher training is also required after unsafe operation, an accident or near miss, a poor evaluation, assignment to a different truck type, or changed conditions. The record must show the operator name, training date, evaluation date, and who trained and evaluated.

OSHA law29 CFR 1910.178(l) via 1926.602(d)
Load Handling Equipment

Do people using below-the-hook devices (spreader bars, lifting beams, clamps) need training?

Yes, under ASME B30.20: operators must be trained in their use according to the manufacturer and the volume.

Consensus standardASME B30.20-2025
Load Handling Equipment

Does ASME lift planning (P30.1) apply to non-crane lifts?

Yes. P30.1 covers planning for all load handling equipment, not just cranes.

Consensus standardASME P30.1-2024
Lift Director

Does OSHA require a qualified lift director on every lift?

No. Federal OSHA sets a lift director qualification only for multiple-crane lifts: someone who meets both competent and qualified person criteria, or a competent person assisted by one or more qualified persons.

Elsewhere OSHA mentions the lift director 'if there is one', for example in agreeing on signals. ASME B30.5 treats the role as always filled.

OSHA law29 CFR 1926.1432(b); 1926.1419
Lift Director

What qualifies a lift director under ASME?

B30.5-2021 lists the lift director's responsibilities. B30.5-2025, effective about 30-Dec-2026, adds qualification criteria.

The new criteria cover knowledge of site and weather hazards, personnel roles, crane limits, rigging, signaling, power lines and regulations, plus the ability to set work-area controls, read load charts and read lift plans. Verify the final wording in the licensed copy.

Consensus standardASME B30.5-2021 / 2025, 5-3.1
Lift Director

When does ASME B30.5-2025 take effect?

About 30-Dec-2026. It was issued 30-Dec-2025 and becomes effective one year after issue. B30.5-2021 applies until then.

Consensus standardASME B30.5-2025 foreword
Lift Director

Do any states or cities require lift director licensing or registration?

Yes. New York City requires DOB lift director registration (since 1-Jan-2025), and Washington State has lift director qualification rules (WAC 296-155 Part L).

Texas projects follow federal OSHA only. See the State & local page.

State / local lawNYC Admin Code 28-424; WAC 296-155
Assembly/Disassembly Director

Who can direct crane assembly or disassembly?

A person who meets the criteria for both a competent person AND a qualified person, or a competent person assisted by one or more qualified persons.

If only one person does the A/D, they must meet both criteria themselves. Job title does not matter.

OSHA law29 CFR 1926.1404(a)
Assembly/Disassembly Director

Must the A/D director review the procedures every time?

Yes, immediately before starting, unless they already understand them and have applied them to the same type and configuration of equipment.

OSHA law29 CFR 1926.1404(b), (c)
Assembly/Disassembly Director

What must the A/D director tell the crew?

Before starting, make sure each crew member understands their tasks, the hazards, and the hazardous positions to avoid. Repeat this for new crew members or changed tasks.

OSHA law29 CFR 1926.1404(d)
Assembly/Disassembly Director

Who must do the rigging during assembly or disassembly?

A qualified rigger.

OSHA law29 CFR 1926.1404(r)(1)
Operator Evaluator

Who can be a crane operator evaluator?

An employee or agent of the employer with the knowledge, training and experience to assess equipment operators.

OSHA does not require evaluator certification. The employer stays responsible for the evaluation even if an agent performs it. Document why each evaluator was designated.

OSHA law29 CFR 1926.1427(f)
Operator Evaluator

Does an operator evaluator need NCCCO practical examiner accreditation?

No. Accreditation is not required for employer evaluations, though it is a useful benchmark for setting evaluator criteria.

Industry practice29 CFR 1926.1427(f)
Operator Evaluator

What does an employer need if it wants to certify operators itself (audited employer program)?

Tests developed by an accredited organization or approved by an independent certified auditor; an audit within 3 months of starting and at least every 3 years; deficiency reporting; audit records kept 3 years.

Certifications issued under this program are not portable and are valid for 5 years.

OSHA law29 CFR 1926.1427(e)
General

Are ASME B30 standards mandatory?

Not by themselves. They become mandatory when adopted by contract, owner spec, state rule or the employer's procedures. OSHA can also use them as evidence of a recognized hazard.

On this site, “Consensus shall” rows are mandatory ASME/ANSI wording and “OSHA law” rows are federal regulation.

OSHA + ASMEOSH Act 5(a)(1); ASME B30 introduction
General

Which crane and rigging roles have a fixed retraining or re-evaluation interval?

Only two: operator certification (5 years maximum) and forklift operator evaluation (at least every 3 years). Everything else is event-driven.

Employers should set their own refresher intervals in procedure.

OSHA law29 CFR 1926.1427; 1910.178(l)(4); 1926.1430(g)(2)
General

Do states add crane rules on top of federal OSHA?

Some do. State-plan states, and cities such as New York, can add licensing or qualification rules. States without a state plan for private employers, such as Texas, follow federal OSHA.

Check the State and local rules page, and check owner, DOE or USACE requirements on government sites.

State / local lawState & local page
Signal Person

Can a rigger signal the crane?

Only if separately qualified as a signal person. Rigger qualification does not include signaling, and anyone may give a stop or emergency-stop signal.

Signal-person qualification requires an oral or written test and a practical test, with documentation at the site listing each signal type.

OSHA law29 CFR 1926.1428; 1926.1419(j)
Signal Person

Who can give an emergency stop signal?

Anyone. A person who becomes aware of a safety problem must alert the operator or signal person with the stop or emergency-stop signal, and the operator must obey it.

OSHA law29 CFR 1926.1419(j); 1926.1417(y)
Rigging Hardware Inspector

Does OSHA require a certified rigging hardware inspector?

No. OSHA requires slings and their fastenings and attachments to be inspected daily by a competent person designated by the employer. There is no OSHA certificate, card or exam for this role.

The employer decides who is competent and designates them. Keep the basis on file: training, experience and a competency check.

OSHA law1926.251(a)(6); 1910.184(d)
Rigging Hardware Inspector

How often must slings and rigging hardware be inspected?

Before use on each shift and as needed during use, with slings inspected daily by the designated competent person. Alloy chain slings also need a thorough periodic inspection at least every 12 months.

ASME adds periodic inspections by a designated person for all slings and hardware: typically yearly in normal service and monthly to quarterly in severe service.

OSHA + ASME1926.251(a)(1), (a)(6), (b)(6); ASME B30.9, B30.26
Rigging Hardware Inspector

Are written inspection records required?

OSHA requires few: the month of the last thorough inspection of each alloy chain sling, and test records for hooks with no manufacturer rating. ASME adds periodic inspection records for slings and dated records for below-the-hook devices.

Daily and before-use inspections need no written record under OSHA, but rejected gear should be tagged and removed.

OSHA + ASME1926.251(b)(6)(ii), (f)(2); ASME B30.9, B30.20
Rigging Hardware Inspector

Is a quarterly color code required?

No. OSHA and ASME require the inspection, not a color code. A color code is a common way to show at a glance that gear is current.

If you use one, post the scheme at the site and keep the records the standards call for. A color tag alone is not a periodic inspection record.

Industry practiceIndustry practice
Rigging Hardware Inspector

What is the difference between a frequent and a periodic inspection?

A frequent inspection is the visual check before use each day or shift, done by the user or another designated person. A periodic inspection is a complete, documented inspection by a designated person at a set interval.

An initial inspection is done before new, repaired or altered gear is first used.

Consensus standardASME B30.9; B30.26; B30.10
Rigging Hardware Inspector

When must a shackle be taken out of service?

When its marking is missing or can't be read; it shows heat damage, weld spatter or arc strikes; it is bent, twisted, stretched, cracked or badly pitted; it is worn 10% or more at any point; the pin doesn't fully engage; or the threads are damaged.

Use only the manufacturer's replacement pin. Check the manufacturer's criteria too, because they can be stricter.

Consensus standardASME B30.26 (paraphrased)
Rigging Hardware Inspector

When must a hook be taken out of service?

Typical criteria: missing ID, cracks, wear over 10% of the original section, a throat opening grown more than the limit (commonly 5%, or per the manufacturer), a twist of more than 10 degrees, a missing or broken latch where one is required, or heat damage.

Repair or welding on a hook is not allowed unless the manufacturer approves it.

Consensus standardASME B30.10 (paraphrased)
Rigging Hardware Inspector

Can a sling with a missing or unreadable tag be used?

No. Without the tag you can't confirm the rated load, so the sling is removed from service until it is re-tagged by the manufacturer or a qualified person, or destroyed.

OSHA requires synthetic web slings to be marked with the manufacturer, rated capacities and material, and alloy chain slings to carry a permanent tag.

OSHA + ASME1926.251(e)(1); 1910.184(e)(1); ASME B30.9
Rigging Hardware Inspector

Who can inspect and load test a spreader bar or lifting beam?

Frequent and periodic inspections are done by a designated person. After an alteration, repair or modification, the device is load tested by or under a qualified person before it goes back into service.

Keep dated periodic inspection records and the load test record. The rated load and other required information must be marked on the device.

Consensus standardASME B30.20
Rigging Hardware Inspector

Do the person using rigging and the person inspecting it need different training?

Usually, yes. The user checks gear before each use. The designated inspector does the complete periodic inspection and decides whether gear stays in service, so they need deeper knowledge of each type of gear and its removal criteria.

One person can do both if the employer has trained and designated them for both.

Consensus standardASME B30.9; B30.26

By standard

Every requirement grouped by the regulation or standard it comes from, OSHA first.

OSHA 29 CFR 1926 – Construction 65

Everyone on the lift

Employer must instruct each employee in recognizing and avoiding unsafe conditions and the regulations applicable to their work environment.

Source: OSHA 29 CFR 1926.21Keep: Training roster / toolbox or orientation recordWhen: Initial; as conditions changeApplies: Construction (29 CFR 1926)
Baseline for every person on a lift team.

Everyone on the lift

Employer must evaluate each employee required to be trained under Subpart CC to confirm the employee understands the information provided in the training.

Source: OSHA 29 CFR 1926 Subpart CCKeep: Evaluation record (quiz, demonstration, sign-off)When: After each required trainingApplies: Construction (29 CFR 1926)
Applies to every Subpart CC training requirement - a sign-in sheet alone does not show understanding.

Everyone on the lift

Refresher training is required when an employee's conduct or an evaluation indicates retraining is necessary.

Source: OSHA 29 CFR 1926 Subpart CCKeep: Retraining record + trigger (incident, observation)When: Event-driven (no fixed interval in OSHA)Applies: Construction (29 CFR 1926)
OSHA sets no calendar refresher for most crane roles; employers should set one in their own procedures.

Everyone on the lift

Training required by Subpart CC must be provided at no cost to the employee.

Source: OSHA 29 CFR 1926 Subpart CCKeep: Cost policyWhen: OngoingApplies: Construction (29 CFR 1926)

Crane Operator

Before operating covered equipment, employer must ensure the operator is trained, certified/licensed, and evaluated. Uncertified persons may operate only as operators-in-training under (b).

Source: OSHA 29 CFR 1926.1427Keep: Training, certification and evaluation recordsWhen: Before first operationApplies: Construction (29 CFR 1926)
Effective 10-Dec-2018; evaluation/documentation provisions effective 7-Feb-2019.
1926.1427(c)-(e)OSHA law

Crane Operator

Operator must hold (c) a qualifying state/local license where required, or (d) certification from an accredited testing organization by equipment type (or type and capacity), or (e) certification through an audited employer program. Valid max 5 years.

Source: OSHA 29 CFR 1926.1427Keep: Copy of license/certification cardWhen: Renew at or before 5 yearsApplies: Construction (29 CFR 1926)
(d) is portable between employers; (e) is not portable.
1926.1427(j)OSHA law

Crane Operator

Certification/licensing must include a written test (controls, performance characteristics, load/capacity calculations, power lines, Appendix C criteria, ground conditions, Subpart CC, ability to read the manual) and a practical test (shift inspection, operational and maneuvering skills, load chart use, shutdown/securing).

Source: OSHA 29 CFR 1926.1427Keep: Testing org / audit recordsWhen: Per certification cycleApplies: Construction (29 CFR 1926)
1926.1427(f)OSHA law

Crane Operator

Employer must ensure each operator is qualified through an evaluation demonstrating skills and knowledge (incl. safety devices, operational aids, configuration) and the ability to safely perform the hoisting activities they will be assigned. A certificate or degree alone does not satisfy this.

Source: OSHA 29 CFR 1926.1427Keep: Signed employer evaluationWhen: Before operating; after retraining; when moving to equipment requiring substantially different skillsApplies: Construction (29 CFR 1926)
Operators employed before 10-Dec-2018 may rely on prior employer assessment.
1926.1427(f)OSHA law

Crane Operator

Evaluation documentation must include the operator's name, evaluator's name and signature, date, and make, model and configuration of equipment used. Must be available at the worksite while the operator works for the employer.

Source: OSHA 29 CFR 1926.1427Keep: Operator evaluation form at the site (paper or electronic)When: Per evaluationApplies: Construction (29 CFR 1926)
Keep a paper copy where electronic records are not available at the site.
1926.1427(b)(1)-(4)OSHA law

Crane Operator

Operator-in-training: formal + practical instruction, tasks within ability, continuous monitoring by a qualified trainer; restricted from power-line proximity, personnel hoisting, multi-crane lifts and lifts over shafts/cofferdams/tank farms; multiple-lift rigging only if trainer judges skills sufficient.

Source: OSHA 29 CFR 1926.1427Keep: OIT log, trainer assignmentWhen: During training periodApplies: Construction (29 CFR 1926)

Crane Operator

Employer must provide retraining when an operator's performance or an evaluation shows the need; operator must then be re-evaluated under (f).

Source: OSHA 29 CFR 1926.1427Keep: Retraining + re-evaluation recordWhen: Event-drivenApplies: Construction (29 CFR 1926)
1926.1427(h)OSHA law

Crane Operator

Tests may be given verbally (with written literacy demonstration) and in any language the candidate understands; the operator may then only run equipment furnished with materials in that language.

Source: OSHA 29 CFR 1926.1427Keep: Language noted on certificateWhen: Per certificationApplies: Construction (29 CFR 1926)
1926.1430(c)OSHA law

Crane Operator

Operators must be trained in safe operation of the equipment they will operate, plus: raising the boom slightly before swinging off a support on friction equipment, and the manufacturer's emergency procedures for halting unintended movement.

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: Initial; refresher as neededApplies: Construction (29 CFR 1926)

Crane Operator

Power-line safety training on the 1408(g) topics (procedures if contact occurs, insulating link limits, de-energizing, etc.).

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: Initial; refresher as neededApplies: Construction (29 CFR 1926)
1926.1430(f)OSHA law

Crane Operator

Tag-out and start-up procedure training (1926.1417(f),(g)) for operators and anyone authorized to start/energize equipment.

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)

Crane Operator

Derricks, sideboom cranes and equipment rated 2,000 lb or less are excluded from 1427 and governed by their own sections (sideboom operators trained per 1430(c)).

Source: OSHA 29 CFR 1926.1427Keep: Per applicable sectionWhen: Per sectionApplies: Construction (29 CFR 1926)
See the Load Handling Equipment User page for these equipment types.
Definition - Qualified rigger / Qualified personOSHA law

Qualified Rigger

A qualified rigger is a rigger who meets the 'qualified person' criteria: a recognized degree, certificate or professional standing, or extensive knowledge, training and experience, AND has successfully demonstrated ability to solve problems related to the work.

Source: OSHA 29 CFR 1926.1401Keep: Employer determination recordWhen: Initial; per task scopeApplies: Construction (29 CFR 1926)
OSHA specifies no exam format or documentation - employer must be able to show the basis.

Qualified Rigger

When employees hook, unhook or guide a load (or make initial connection) within the fall zone, the materials must be rigged by a qualified rigger.

Source: OSHA 29 CFR 1926.1425Keep: Lift plan / JHA shows QR assignedWhen: Each such liftApplies: Construction (29 CFR 1926)

Qualified Rigger

Rigging work during assembly/disassembly must be done by a qualified rigger.

Source: OSHA 29 CFR 1926.1404Keep: A/D plan shows QR assignedWhen: Each A/DApplies: Construction (29 CFR 1926)
1926.1430(d)OSHA law

Qualified Rigger

Competent persons and qualified persons must be trained in the Subpart CC requirements applicable to their duties.

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)

Qualified Rigger

Steel erection: employees engaged in multiple lift rigging must receive specific training in the procedure and hazards.

Source: OSHA 29 CFR 1926 Subpart RKeep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)
Only where Christmas-treeing is used.

Qualified Rigger

Rigging equipment must be inspected before use on each shift and as necessary during use; defective equipment is removed from service.

Source: OSHA 29 CFR 1926.251Keep: Inspection practice / tag systemWhen: Each shiftApplies: Construction (29 CFR 1926)

Qualified Rigger

Each day before use, a competent person designated by the employer inspects slings and all fastenings and attachments for damage or defects; damaged or defective slings are removed from service immediately.

Source: OSHA 29 CFR 1926.251Keep: Inspection record / tag systemWhen: Daily before useApplies: Construction (29 CFR 1926)
1926.1428(a)(1)-(2)OSHA law

Signal Person

Before giving any signals, signal person must be qualified via (1) documentation from a third-party qualified evaluator (portable) or (2) assessment by the employer's qualified evaluator (not portable).

Source: OSHA 29 CFR 1926.1428Keep: Third-party card or employer assessmentWhen: Before first signalApplies: Construction (29 CFR 1926)

Signal Person

Documentation must be available at the site while the person works for the employer and must state each type of signaling (hand, radio, etc.) the person is qualified for.

Source: OSHA 29 CFR 1926.1428Keep: Qualification doc at site, signal types listedWhen: OngoingApplies: Construction (29 CFR 1926)
1926.1428(c)(1)-(5)OSHA law

Signal Person

Must know and apply the signal types used (Standard Method for hand signals where applicable), understand basic equipment operation and limits (incl. dynamics of swinging/stopping loads and boom deflection), know 1926.1419-.1422 and .1428, and demonstrate this through an oral or written test AND a practical test.

Source: OSHA 29 CFR 1926.1428Keep: Test results (oral/written + practical)When: InitialApplies: Construction (29 CFR 1926)
1926.1428(b)OSHA law

Signal Person

If later actions show the person no longer meets requirements, employer must stop them from signaling until retrained and reassessed.

Source: OSHA 29 CFR 1926.1428Keep: Removal + retraining + reassessment recordWhen: Event-drivenApplies: Construction (29 CFR 1926)
1926.1430(b)OSHA law

Signal Person

Signal persons who do not meet 1428(c) must be trained in the areas addressed in that paragraph.

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: Before qualificationApplies: Construction (29 CFR 1926)
1926.1419(a), (c)(2); 1926.1421(a)OSHA law

Signal Person

A signal person must be provided when the point of operation is not in full view of the operator, when the view in the direction of travel is obstructed, or when the operator or person handling the load decides one is needed. Non-standard hand signals and voice signals must be agreed in advance by the operator, signal person and lift director (if any).

Source: OSHA 29 CFR 1926.1419-.1422Keep: Lift plan / pre-lift briefingWhen: Each liftApplies: Construction (29 CFR 1926)

Lift Crew Member

Each employee who works with the equipment must be trained to keep clear of holes and crush/pinch points and on the work-area-control (swing radius) hazards of 1926.1424.

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)
Tag-line handlers, helpers, spotters, laborers in the work zone.

Lift Crew Member

Employees covered by 1408(g) and 1410(m) (crew working near power lines) trained on power-line hazards and procedures.

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)
Definition - Dedicated spotter (power lines)OSHA lawVerify

Lift Crew Member

A dedicated spotter for power-line encroachment must meet the signal person qualification requirements of 1926.1428 and be positioned/assigned per the standard.

Source: OSHA 29 CFR 1926.1401Keep: Signal-person qualification docWhen: Before assignmentApplies: Construction (29 CFR 1926)
Verify definition wording; treat spotters as signal persons.
1926.1430(f)OSHA law

Lift Crew Member

Any employee authorized to start/energize equipment or operate its controls (e.g., maintenance) trained in tag-out and start-up procedures.

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)
1926.1425(b),(d),(e)OSHA law

Lift Crew Member

Only employees needed to hook/unhook/guide or receive the load may be in the fall zone; none directly under the load (limited exception for tilt-up/down).

Source: OSHA 29 CFR 1926.1425Keep: Work area control / JHAWhen: Each liftApplies: Construction (29 CFR 1926)
1926.1431(m)OSHA law

Lift Crew Member

Personnel hoisting: pre-lift meeting attended by the operator, signal person (if used), employees to be hoisted and the person responsible for the task; held before the trial lift at each new work location and repeated for newly assigned employees.

Source: OSHA 29 CFR 1926.1431Keep: Pre-lift meeting recordWhen: Each personnel hoisting job / new workerApplies: Construction (29 CFR 1926)

Lift Crew Member

Multiple-crane lifts: lift director reviews the plan in a meeting with all workers who will be involved.

Source: OSHA 29 CFR 1926.1432Keep: Meeting recordWhen: Each multi-crane liftApplies: Construction (29 CFR 1926)
1926.1404(d)OSHA law

Lift Crew Member

A/D crew members instructed on their tasks, hazards and hazardous positions before starting; repeated for new crew/changed tasks.

Source: OSHA 29 CFR 1926.1404Keep: A/D briefing recordWhen: Each A/DApplies: Construction (29 CFR 1926)

Load Handling Equipment User

General hazard instruction - the only explicit OSHA training duty for most non-crane LHE (chain/lever hoists, jacks, rollers, gantries, winches).

Source: OSHA 29 CFR 1926.21Keep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)
OSHA gap - ASME B30 volumes carry the detail.
1926.554(a); 1926.553(a)OSHA lawVerify

Load Handling Equipment User

Overhead hoists operated within manufacturer limits; base-mounted drum hoists meet the incorporated ANSI B30.7 edition.

Source: OSHA 29 CFR 1926.554 / 1926.553Keep: Manufacturer manual on siteWhen: OngoingApplies: Construction (29 CFR 1926)
1926.1440; 1926.1441OSHA lawVerify

Load Handling Equipment User

Sideboom operators trained per 1430(c); operators of equipment rated 2,000 lb or less trained per 1441.

Source: OSHA 29 CFR 1926.1440 / .1441Keep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)

Lift Director

Multiple-crane/derrick lifts must be directed by a person who meets the criteria for both a competent and a qualified person, or a competent person assisted by one or more qualified persons (lift director).

Source: OSHA 29 CFR 1926.1432Keep: Designation + basis of qualificationWhen: Each multi-crane liftApplies: Construction (29 CFR 1926)
Only explicit OSHA lift-director qualification trigger.

Lift Director

Lift director reviews the multi-crane plan in a meeting with all workers who will be involved.

Source: OSHA 29 CFR 1926.1432Keep: Meeting recordWhen: Each multi-crane liftApplies: Construction (29 CFR 1926)

Lift Director

Where there is a lift director, he/she participates with operator and signal person in agreeing on signals/voice communication.

Source: OSHA 29 CFR 1926.1419-.1422Keep: Pre-lift briefingWhen: Each liftApplies: Construction (29 CFR 1926)
OSHA otherwise uses 'lift director' without separate qualification criteria.
1926.1430(d)OSHA law

Lift Director

As a competent/qualified person, trained in Subpart CC requirements applicable to the role.

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)
1926.1404(a)(1)-(2)OSHA law

Assembly/Disassembly Director

Assembly/disassembly must be directed by a person meeting criteria for both competent and qualified person, or a competent person assisted by one or more qualified persons; if one person does the work, they must be both.

Source: OSHA 29 CFR 1926.1404Keep: A/D director designation + basisWhen: Each A/DApplies: Construction (29 CFR 1926)
Applies regardless of job title.
1926.1404(b)OSHA law

Assembly/Disassembly Director

A/D director must understand the applicable assembly/disassembly procedures.

Source: OSHA 29 CFR 1926.1404Keep: Procedure on siteWhen: Each A/DApplies: Construction (29 CFR 1926)
1926.1404(c)OSHA law

Assembly/Disassembly Director

Review the applicable procedures immediately before starting, unless already understood and previously applied to the same type and configuration of equipment.

Source: OSHA 29 CFR 1926.1404Keep: Review sign-offWhen: Each A/DApplies: Construction (29 CFR 1926)
1926.1404(d)OSHA law

Assembly/Disassembly Director

Ensure crew members understand their tasks, hazards and hazardous positions before starting, and when tasks change or new personnel join.

Source: OSHA 29 CFR 1926.1404Keep: Crew briefing recordWhen: Each A/D / changeApplies: Construction (29 CFR 1926)

Assembly/Disassembly Director

Use manufacturer procedures or employer procedures developed by a qualified person; address site/ground, blocking, boom support, pin removal, component weights, wind and other listed hazards.

Source: OSHA 29 CFR 1926.1403-.1406Keep: A/D planWhen: Each A/DApplies: Construction (29 CFR 1926)

Assembly/Disassembly Director

A/D rigging work done by a qualified rigger.

Source: OSHA 29 CFR 1926.1404Keep: A/D planWhen: Each A/DApplies: Construction (29 CFR 1926)
1926.1430(d)OSHA law

Assembly/Disassembly Director

Trained in Subpart CC requirements applicable to A/D director duties.

Source: OSHA 29 CFR 1926.1430Keep: Training recordWhen: InitialApplies: Construction (29 CFR 1926)
1926.1435OSHA lawVerify

Assembly/Disassembly Director

Tower cranes: erecting, climbing and dismantling provisions (A/D director duties apply; pre-erection inspection).

Source: OSHA 29 CFR 1926.1435Keep: Erection planWhen: Each erection/climbApplies: Construction (29 CFR 1926)
1926.1427(f)OSHA law

Operator Evaluator

Evaluator must have the knowledge, training and experience necessary to assess equipment operators, and be an employee or agent of the employer. Employer remains responsible for compliance.

Source: OSHA 29 CFR 1926.1427Keep: Evaluator designation + basis (resume, certs)When: Before evaluatingApplies: Construction (29 CFR 1926)
OSHA does not require evaluator certification.
1926.1427(f)OSHA law

Operator Evaluator

Evaluator name and signature recorded on each operator evaluation, with date and equipment make/model/configuration.

Source: OSHA 29 CFR 1926.1427Keep: Signed evaluation formWhen: Per evaluationApplies: Construction (29 CFR 1926)

Operator Evaluator

Operator trainer (for operators-in-training): employee/agent with knowledge, training and experience to direct the trainee; no tasks that detract from monitoring; line-of-sight + communication (direct communication for tower cranes).

Source: OSHA 29 CFR 1926.1427Keep: Trainer designationWhen: During OITApplies: Construction (29 CFR 1926)
Trainer and evaluator may be the same person.
1926.1427(e)OSHA law

Operator Evaluator

If an employer runs an audited employer certification program: tests developed by an accredited organization or approved by an independent certified auditor; audit within 3 months of start and at least every 3 years; deficiencies reported; records kept 3 years.

Source: OSHA 29 CFR 1926.1427Keep: Audit reportsWhen: ≤3 months, then ≤3 yearsApplies: Construction (29 CFR 1926)
Certifications non-portable.
Definition - Qualified evaluator (not a third party)OSHA law

Operator Evaluator

Employer's signal-person evaluator must be employed by the signal person's employer and have demonstrated competence in accurately assessing signal persons against 1428.

Source: OSHA 29 CFR 1926.1401 / 1926.1428Keep: Evaluator designationWhen: Before evaluatingApplies: Construction (29 CFR 1926)
Included because operator evaluators often also assess signal persons.

Rigging Hardware Inspector

Each day before use, a competent person designated by the employer inspects slings and all fastenings and attachments. Damaged or defective slings are removed from service immediately.

Source: OSHA 29 CFR 1926.251Keep: Inspector designation list; tag or removal recordWhen: Daily before useApplies: Construction (29 CFR 1926)
This is the rule that creates the inspector role in construction. OSHA does not say how the person is trained or tested.

Rigging Hardware Inspector

Rigging equipment is inspected before use on each shift and as needed during use. Defective rigging equipment is removed from service.

Source: OSHA 29 CFR 1926.251Keep: Inspection practice / tag-out of rejected gearWhen: Each shift; during useApplies: Construction (29 CFR 1926)

Rigging Hardware Inspector

Alloy steel chain slings get a thorough periodic inspection at an interval set by frequency of use, severity of service, the nature of the lifts and service-life experience, and never more than 12 months apart. The employer keeps a record of the most recent month each chain sling was thoroughly inspected.

Source: OSHA 29 CFR 1926.251Keep: Periodic inspection record (month) per chain slingWhen: At least every 12 monthsApplies: Construction (29 CFR 1926)
The only fixed sling inspection interval in federal OSHA.

Rigging Hardware Inspector

Hook ratings follow the manufacturer's recommendations. A hook with no manufacturer recommendation is tested to twice its intended safe working load before first use, and the employer keeps a record of the test dates and results.

Source: OSHA 29 CFR 1926.251Keep: Hook test recordWhen: Before first useApplies: Construction (29 CFR 1926)
1926.251(a)(4)OSHA lawVerify

Rigging Hardware Inspector

Custom-designed grabs, hooks, clamps and other lifting accessories for items such as modular panels and prefabricated structures are marked with their safe working load and proof tested to 125% of rated load before use.

Source: OSHA 29 CFR 1926.251Keep: Marking + proof test recordWhen: Before first useApplies: Construction (29 CFR 1926)
Confirm the paragraph number on osha.gov.
1926.251(c)(4)(iv)OSHA lawVerify

Rigging Hardware Inspector

Wire rope is removed from use if, in any length of eight diameters, visible broken wires exceed 10% of the total wires, or the rope shows other signs of excessive wear, corrosion or defect.

Source: OSHA 29 CFR 1926.251Keep: Removal record / tagWhen: Each inspectionApplies: Construction (29 CFR 1926)
ASME B30.9 uses a different broken-wire count for slings. Apply whichever your procedure adopts, and never the less strict of the two.
1926.251(e)(8)OSHA lawVerify

Rigging Hardware Inspector

Synthetic web slings are removed from service for acid or caustic burns, melting or charring, snags, punctures, tears or cuts, broken or worn stitches, or distorted fittings.

Source: OSHA 29 CFR 1926.251Keep: Removal record / tagWhen: Each inspectionApplies: Construction (29 CFR 1926)
1926.1431(j)OSHA lawVerify

Rigging Hardware Inspector

Crane-suspended personnel platforms and their rigging are proof tested to 125% of the platform's rated capacity at each jobsite before hoisting employees, and after any repair or modification.

Source: OSHA 29 CFR 1926.1431Keep: Proof test recordWhen: Each jobsite; after repairApplies: Construction (29 CFR 1926)
See also the trial lift and inspection provisions of 1926.1431 and ASME B30.23.

OSHA 29 CFR 1910 – General industry 9

Crane Operator

General industry: only designated persons may operate overhead/gantry cranes and crawler/locomotive/truck cranes. No OSHA certification rule in 1910.

Source: OSHA 29 CFR 1910 Subpart NKeep: Designation listWhen: OngoingApplies: General industry (29 CFR 1910)
For plant/fabrication-shop work under 1910; ASME B30 fills the qualification gap.
1910.184(d)OSHA law

Qualified Rigger

General industry: slings and fastenings/attachments inspected each day before use by a competent person designated by the employer.

Source: OSHA 29 CFR 1910.184Keep: Inspection recordWhen: DailyApplies: General industry (29 CFR 1910)
No 1910 ruleIndustry practice

Signal Person

General industry has no OSHA signal-person qualification rule; employer relies on ASME B30 and the OSH Act General Duty Clause.

Source: OSHA 29 CFR 1910 Subpart NKeep: Signal-person qualification record (recommended)When: Per employer policyApplies: General industry (29 CFR 1910)
Apply 1428-equivalent qualification company-wide for consistency.
1910.178(l)(1)-(3)OSHA law

Load Handling Equipment User

Powered industrial truck (forklift/telehandler) operators: formal + practical training and workplace evaluation before operating; trainees only under direct supervision.

Source: OSHA 29 CFR 1910.178 (via 1926.602(d))Keep: Training + evaluation recordWhen: Before operatingApplies: Construction & general industry
Include if forklifts/telehandlers are used as LHE.

Load Handling Equipment User

Refresher training and evaluation after unsafe operation, accident/near miss, poor evaluation, new truck type or changed conditions; performance evaluated at least once every 3 years.

Source: OSHA 29 CFR 1910.178Keep: Evaluation recordWhen: At least every 3 years + event-drivenApplies: Construction & general industry
The only fixed re-evaluation interval OSHA sets for these roles. Crane operator certification must also be renewed at least every 5 years.

Load Handling Equipment User

Employer certifies each operator was trained and evaluated: operator name, training date, evaluation date, identity of trainer/evaluator.

Source: OSHA 29 CFR 1910.178Keep: Certification recordWhen: Each training/evalApplies: Construction & general industry

Operator Evaluator

Forklift trainers/evaluators must have the knowledge, training and experience to train operators and evaluate competence.

Source: OSHA 29 CFR 1910.178Keep: Trainer designationWhen: Before evaluatingApplies: Construction & general industry
If evaluators also cover forklift/telehandler.
1910.184(d)OSHA law

Rigging Hardware Inspector

General industry: slings and their fastenings and attachments are inspected each day before use by a competent person designated by the employer; damaged or defective slings are removed from service.

Source: OSHA 29 CFR 1910.184Keep: Inspector designation listWhen: Daily before useApplies: General industry (29 CFR 1910)

Rigging Hardware Inspector

General industry: alloy steel chain slings in use get a thorough inspection at least once every 12 months, with a record of the most recent month inspected.

Source: OSHA 29 CFR 1910.184Keep: Periodic inspection record (month) per chain slingWhen: At least every 12 monthsApplies: General industry (29 CFR 1910)

ASME B30.5 – Mobile and locomotive cranes 13

5-3.1.2 Operator qualificationsConsensus “shall”Verify

Crane Operator

Operator qualification by written and practical examination specific to the crane type, via certification, licensing or employer program; employer documents qualification.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Qualification fileWhen: Per qualificationApplies: All industries (consensus)
Paraphrased - verify exact text/subparagraph in licensed copy.
5-3.1.2 Physical qualificationsConsensus “should”Verify

Crane Operator

Physical/medical criteria (vision, depth perception, color perception, hearing, no condition causing sudden loss of control) and substance-use provisions - mix of 'shall' and 'should' items.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Medical/fitness record (keep separate from training file)When: Per employer policyApplies: All industries (consensus)
Verify which items are 'shall' vs 'should'.
5-3.1.2 Operator familiarizationConsensus “shall”Verify

Crane Operator

Before operating a specific crane, operator is familiarized with its controls, manual, load charts and configuration.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Familiarization checklistWhen: Each new crane model/configApplies: All industries (consensus)
B30.5 rigger qualifications — clause pending verificationConsensus “shall”Verify

Qualified Rigger

For rigging tasks, verify when a qualified rigger is required by the applicable OSHA rule or governing standard; do not assume a blanket qualified-rigger staffing rule for all crane use. Confirm applicable evidence of qualification for: selection/use of rigging hardware; application of standard hitches; estimating load weight, center of gravity, sling angles/loading and load movement; and inspection of rigging equipment.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Written + practical exam results; employer designationWhen: Initial; per programApplies: All industries (consensus)
Exam may be administered by anyone covering the competencies (CCO Rigger II is commonly cited as meeting them). Verify clause number.
B30.5 rigger supervision — clause pending verificationConsensus “shall”Verify

Qualified Rigger

Personnel performing rigging tasks who are not yet qualified must work under the direct supervision of a qualified rigger.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Supervisor assignment recordWhen: While not qualifiedApplies: All industries (consensus)
Clause number reported by industry sources; verify in the licensed copy.
5-3.1 Rigger responsibilities (added 2018)Consensus “shall”Verify

Qualified Rigger

Rigger selects, configures and assembles rigging for attaching, supporting, controlling and detaching the load, and confirms rigging suitability/condition.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Task assignmentWhen: Each liftApplies: All industries (consensus)
5-3.1 Signalperson qualifications & responsibilities (responsibilities added 2021)Consensus “shall”Verify

Signal Person

Signalperson qualified in standard signals, basic crane operation and limitations, with demonstration by oral/written and practical exam; 2021 added explicit signalperson responsibilities.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Qualification fileWhen: InitialApplies: All industries (consensus)
Verify exact qualification text in 2021 vs 2025 edition.
5-3.3 SignalsConsensus “shall”Verify

Signal Person

Standard hand signals used and available at the site; special signals agreed in advance; one designated signalperson at a time; operator obeys stop from anyone.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Pre-lift briefingWhen: Each liftApplies: All industries (consensus)
5-3.1 Responsibilities (lift director duties)Consensus “shall”Verify

Lift Crew Member

Lift director ensures personnel involved understand their roles and that a pre-lift briefing is held; anyone may signal emergency stop.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Pre-lift briefingWhen: Each liftApplies: All industries (consensus)
5-3.1 Lift director responsibilitiesConsensus “shall”Verify

Lift Director

Lift director directly oversees the crane work and rigging crew: confirms lift needs and crane suitability, ensures personnel are qualified and understand roles, holds pre-lift briefing, controls work area, stops work when unsafe.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Lift plan / briefingWhen: Each liftApplies: All industries (consensus)
B30.5-2025 lift director qualifications — clause pending verificationConsensus “shall”Verify

Lift Director

New lift director qualification requirement: evidence of satisfactory demonstration of knowledge of site/weather hazards, personnel roles and qualifications, crane characteristics and limits, rigging equipment, signaling, power lines, special lifts, applicable regulations; and ability to set traffic/access controls, place personnel, read/write/do arithmetic, read load charts, and read and discuss lift plans.

Source: ASME B30.5-2025 (effective ~30-Dec-2026)Keep: Written exam + documentation recommendedWhen: Before assignment (from effective date)Applies: All industries (consensus)
Based on the public-review draft reported Nov 2024; confirm the final 2025 text.
Assembly/disassembly provisionsConsensus “shall”Verify

Assembly/Disassembly Director

Assembly/disassembly performed per manufacturer instructions under direction of a designated qualified person.

Source: ASME B30.5 / B30.3-2025Keep: A/D planWhen: Each A/DApplies: All industries (consensus)
Verify clause text.
5-3.1.2 Operator qualification (practical exam)Consensus “shall”Verify

Operator Evaluator

Practical operating exam administered/observed by a designated or qualified person.

Source: ASME B30.5-2021 (in effect) / B30.5-2025 (effective ~30-Dec-2026)Keep: Evaluator designationWhen: Per examApplies: All industries (consensus)
Verify term used in 2021/2025.

ASME B30 – Other volumes 13

Personnel competence (each B30 volume)Consensus “shall”Verify

Everyone on the lift

Persons performing functions identified in the volume must meet its qualifying criteria and be trained in and familiar with the volume, through education, training, experience, skill and physical fitness as necessary.

Source: ASME B30 series (all volumes)Keep: Qualification file per personWhen: Initial; maintainApplies: All industries (consensus)
Paraphrased; confirm wording in the licensed copy of each volume you rely on.
Ch. 2-3 / 17-3 Operator TrainingConsensus “shall”Verify

Crane Operator

Overhead and underhung crane operators must be trained and qualified per the volume's operator training chapter.

Source: ASME B30.2-2022 / B30.17-2026Keep: Training/qualification recordWhen: Initial; refresher per programApplies: All industries (consensus)
Shop / facility cranes.
Training section (each sling chapter)Consensus “shall”Verify

Qualified Rigger

Sling users must be trained in selection, inspection, cautions to personnel, environmental effects and rigging practices.

Source: ASME B30.9-2025 SlingsKeep: Training recordWhen: Initial; refresher per programApplies: All industries (consensus)
Published 18-Jul-2025; check effective date in foreword.
Training sectionConsensus “shall”Verify

Qualified Rigger

Rigging hardware users must be trained in selection, inspection, cautions, environmental effects and rigging practices.

Source: ASME B30.26-2026 Rigging HardwareKeep: Training recordWhen: InitialApplies: All industries (consensus)
Jacks, rollers, air casters, hydraulic gantriesConsensus “shall”Verify

Load Handling Equipment User

Operators/users of jacks, rollers, air casters and hydraulic gantries trained and competent per personnel competence and operation chapters.

Source: ASME B30.1-2026Keep: Training recordWhen: InitialApplies: All industries (consensus)
Operator training & operation chaptersConsensus “shall”Verify

Load Handling Equipment User

Overhead (underhung) and lever hoist operators trained; B30.21-2025 adds that signal/communication means be established before operating when signals are needed.

Source: ASME B30.16-2022 / B30.21-2025Keep: Training recordWhen: InitialApplies: All industries (consensus)
B30.21-2025 effective 10-Feb-2026.
Winches - operationConsensus “shall”Verify

Load Handling Equipment User

Winch operators trained/qualified per volume.

Source: ASME B30.7-2026Keep: Training recordWhen: InitialApplies: All industries (consensus)
Below-the-hook lifting devices - operationConsensus “shall”Verify

Load Handling Equipment User

Operators of BTH devices trained in use per manufacturer and volume.

Source: ASME B30.20-2025Keep: Training recordWhen: InitialApplies: All industries (consensus)
Personnel lifting systemsConsensus “shall”Verify

Load Handling Equipment User

Personnel lifting participants trained and pre-lift meeting held.

Source: ASME B30.23-2022Keep: Meeting recordWhen: Each jobApplies: All industries (consensus)
Inspection sections (each volume)Consensus “shall”Verify

Rigging Hardware Inspector

Inspections are grouped as initial (before first use), frequent (each day or shift the gear is used, by the user or another designated person) and periodic (a complete inspection by a designated person, at an interval based on service).

Source: ASME B30.9 / B30.26 / B30.10Keep: Designated person list; periodic inspection record where the volume requires oneWhen: Initial; each shift; periodicApplies: All industries (consensus)
Paraphrased. Typical periodic intervals: normal service yearly, severe service monthly to quarterly, special service as a qualified person recommends.
Inspection records (each sling chapter)Consensus “shall”Verify

Rigging Hardware Inspector

A written record of the most recent periodic inspection is kept for slings.

Source: ASME B30.9-2025 SlingsKeep: Periodic inspection record per sling (or per lot/ID)When: Each periodic inspectionApplies: All industries (consensus)
Confirm which sling types and what the record must show in the licensed copy.
Periodic inspectionConsensus “shall”Verify

Rigging Hardware Inspector

Below-the-hook devices get frequent and periodic inspections at intervals set by service class, with dated records of periodic inspections. A device that has been altered, repaired or modified is load tested by or under a qualified person before return to service, at no more than 125% of rated load unless the manufacturer says otherwise.

Source: ASME B30.20-2025 Below-the-Hook Lifting DevicesKeep: Dated periodic inspection record; load test recordWhen: Per service class; after repairApplies: All industries (consensus)
Inspection sectionsConsensus “shall”Verify

Rigging Hardware Inspector

Hand chain and lever hoists get frequent inspections (hook, load chain, brake and controls) and periodic inspections by a designated person, with removal criteria for the load chain, hook and brake.

Source: ASME B30.16 / B30.21Keep: Periodic inspection recordWhen: Frequent; periodic per serviceApplies: All industries (consensus)
Hooks on hoists also follow B30.10.

ASME P30.1 – Planning for load handling 3

Personnel / pre-lift meeting sectionsConsensus “should”Verify

Lift Crew Member

Personnel involved in the load handling activity are identified, informed of roles and hazards, and attend a pre-lift meeting appropriate to the lift category (standard vs critical).

Source: ASME P30.1-2024Keep: Lift plan sign-offWhen: Each liftApplies: All industries (consensus)
Published 7-Feb-2025.
Scope - all LHEConsensus “should”Verify

Load Handling Equipment User

Planning, roles and pre-lift meeting provisions apply to all load handling equipment, not just cranes.

Source: ASME P30.1-2024Keep: Lift planWhen: Each liftApplies: All industries (consensus)
Lift director roleConsensus “should”Verify

Lift Director

Lift director verifies the lift category, reviews and implements the lift plan, conducts pre-lift meeting and post-lift review.

Source: ASME P30.1-2024Keep: Lift planWhen: Each liftApplies: All industries (consensus)

ANSI/ASSP A10.42 – Rigging qualifications 1

Whole standardConsensus “should”Verify

Qualified Rigger

Sets minimum knowledge and performance criteria for a qualified rigger in construction and demolition, and related responsibilities.

Source: ANSI/ASSP A10.42-2000 (R2017)Keep: Qualification fileWhen: Per programApplies: Construction (29 CFR 1926)
Voluntary; useful as a competency checklist for an employer's own rigger exam.

Industry programs 3

Examiner accreditationIndustry practice

Operator Evaluator

Accredited bodies accredit practical examiners for certification exams. Not required for employer evaluations.

Source: NCCCO / NCCER practical examiner programsKeep: Examiner accreditationWhen: Per bodyApplies: All industries (voluntary)
A useful benchmark when setting evaluator qualification criteria.
Inspector competencyIndustry practice

Rigging Hardware Inspector

Employers commonly qualify inspectors through classroom training on each type of gear and its removal criteria, supervised inspections, and a documented competency check before designation, with refreshers when gear or procedures change.

Source: Employer programKeep: Training + competency record; designationWhen: Before designation; refresher per programApplies: All industries (voluntary)
Good practice, not a federal rule. Awareness modules on this site do not train or qualify anyone.
Color-code programsIndustry practice

Rigging Hardware Inspector

Many sites mark the latest periodic inspection with a color code by month or quarter, often with a second mark for the year. OSHA and ASME do not require color codes. They require the inspection, and records where noted.

Source: Employer programKeep: Posted color scheme + inspection recordsWhen: Per programApplies: All industries (voluntary)
A color tag shows the gear was inspected. It does not replace a required written record.

State & local rules

Federal OSHA is the floor. States with their own OSHA plans, and some cities, add licensing or qualification rules. Check before mobilizing, and check owner or agency requirements on government sites. This table lists examples, not every jurisdiction.

JurisdictionRuleRoles affectedWhat it adds
Washington (L&I DOSH)WAC 296-155 Part L (comprehensive update WSR 25-16-089, Aug 2025; qualified evaluator definition corrected by WSR 25-24-087, effective 2 Jan 2026)Lift Director, A/D Director, certain operators, Rigger, Signal personState-specific qualification requirements for lift directors and A/D directors using qualified evaluators (employer or third party); state rigger qualification.
Washington (tower cranes)Tower crane permit rules (WSR 25-22-085, effective 5 Dec 2025)A/D Director, OperatorFrom 1 Jan 2026, prime contractors need an L&I permit before operating, assembling, disassembling or reconfiguring a tower crane, including a safety conference and notifications.
California (Cal/OSHA)Title 8 §5001.3 (signal person) and related crane sectionsSignal person, OperatorMirrors 1926.1428; California also has its own operator certification and crane rules.
New York City (DOB)NYC Admin Code §28-424; 1 RCNY §3319-02Lift DirectorLift directors must be registered with DOB (or be a licensed Master Rigger or supervised Master Rigging Foreman). Registration requires a Department-approved 32-hour lift director course plus one of: an NCCCO Lift Director certification, 2 years supervising rigging in NYC, 3 years holding a DOB hoisting machine operator license, or 1 year of NYC lift director experience.
TexasFederal OSHA jurisdiction (no state plan for private employers)AllNo state overlay for private employers; federal OSHA applies.
Other state plans / ownersCheck before mobilizingAllSeveral states license operators; DOE (DOE-STD-1090), USACE (EM 385-1-1) and owner specs may add requirements on government/NS&E sites.

What's changing

Recent and upcoming edition changes that affect lift-team qualifications, and changes to this site.

16 Nov 2026
New: Pre-Mobilization Training Checklist (Form 8, Rev 0)

A per-worker self-assessment for any employer: confirm that required training, testing, evaluation and records are complete for each assigned role before the worker mobilizes. Word and print-ready PDF. Download the forms

16 Nov 2026
Training modules are now awareness modules

The eight modules cover what the standards require for each role and for the employer. They do not train, test or qualify anyone, and the written exams are now awareness checks. Audience: managers, training coordinators, supervisors and evaluators who run or verify a crane and rigging training and qualification program. Slides, checks, answer keys, scoring sheets and instructor packages have new revisions. Download the modules

16 Nov 2026
New: Rigging and lifting role and authorization matrix (Rev 0)

One table shows which roles may do which lift tasks, from the fall zone to directing the lift, with the controlling condition, citation and source type for each row. Excel and printable PDF downloads. Open the role matrix

15 Nov 2026
New: Rigging hardware section and Rigging Hardware Inspector role

A Rigging hardware page summarizes inspection types and removal criteria for slings, shackles, hooks, below-the-hook devices, clamps, hoists and personnel platforms. A ninth role page covers the designated inspector under 1926.251(a)(6). Rigging Hardware Inspector

~30 Dec 2026
ASME B30.5-2025 Mobile and Locomotive Cranes becomes effective

Replaces B30.5-2021 one year after its 30 Dec 2025 issue. Reported to add qualification criteria for lift directors. Next edition scheduled for 2028. Lift Director

14 Nov 2026
Site refresh: lift diagram and role icons

The home page now shows a crane lift with each of the eight roles marked; select one to open its page. Each role has its own icon and color across the role pages, training modules and menus.

14 Nov 2026
Seven blank field forms added (Rev 0)

Crew qualification roster, operator evaluation record, signal person qualification record, pre-lift meeting sign-in, crane shift and rigging gear inspection checklists, and a before-you-show-up records checklist. Editable Word, printable on one letter sheet. Download the forms

14 Nov 2026
Signal Person module updated (Rev 1)

Adds OSHA's Appendix A hand signal chart (slide 8) and a best working practices slide of field lessons, labeled as good practice, not requirements (slide 15). Instructor package delivery plan renumbered to match. Download the modules

14 Nov 2026
Site and training resource corrections

Citation corrections in Modules 3, 5 and 8 and in the role pages, the NYC and Washington rows updated, and internal review notes removed from the Module 6–8 instructor packages.

14 Nov 2026
Training resources released (Rev 0)

Free supplemental training modules for eight roles (Modules 1–5 peer reviewed; ASME items in 6–8 marked Verify): PowerPoint slide decks and Word instructor packages. Download the modules

1 Jan 2026
Washington tower crane permits

Prime contractors need an L&I permit before tower crane operation, assembly, disassembly or reconfiguration (WSR 25-22-085). Assembly/Disassembly Director

10 Feb 2026
ASME B30.21-2025 Lever Hoists effective

Adds that a means of communication must be established before operating when signals are needed. Load Handling Equipment User

2025
ASME P30.1-2024 Planning for Load Handling Activities published (7 Feb 2025)

Current lift-planning standard for all load handling equipment. Lift Director

2025
ASME B30.9-2025 Slings published (18 Jul 2025)

Sling user training, inspection and removal criteria. Qualified Rigger

Aug-Sep 2025
Washington State WAC 296-155 Part L update

State qualification requirements for lift directors and A/D directors using qualified evaluators. Evaluator definition corrected effective 2 Jan 2026 (WSR 25-24-087). Lift Director

1 Jan 2025
New York City lift director registration

Anyone acting as lift director in NYC must be DOB-registered or a licensed Master Rigger (or supervised Master Rigging Foreman). Lift Director

7 Feb 2019
OSHA employer evaluation and documentation for crane operators

Certification alone is no longer enough; employers must evaluate and document each operator. Crane Operator

Awareness modules

Free awareness modules for eight of the nine referenced roles (Rigging Hardware Inspector does not yet have a dedicated module). Each covers what the standards require for the role and for the employer, with editable PowerPoint slides, a 25-question awareness check, an answer key, answer and scoring sheets, and an instructor package. Audience: managers, training coordinators, supervisors and evaluators who run or verify a crane and rigging training and qualification program.

Important. Awareness only. These modules do not train, test or qualify anyone to perform a role, and the awareness checks are not qualification tests. They are not a training program for any role, and not a qualification, certification or license. Job-specific training, practical evaluation, qualification and records are the employer’s responsibility. The Pre-Mobilization Training Checklist (Form 8) helps confirm they are complete.

Website v3.3 trial · 17 Nov 2026. The modules are now labeled awareness modules: written exams are awareness checks, and the slides, answer keys, scoring sheets and instructor packages were revised to match. Check each file’s revision. Verify adopted ASME provisions against the applicable licensed editions.

Module 1 · Signal PersonRev 3

When a signal person is required, qualification and documentation, hand and voice signals, radio communication, stopping and dedicated power-line spotting.

Basis: 1926.1419–.1422, .1428 · Role requirements

Module 2 · Lift Crew MemberRev 2

Swing and crush hazards, fall-zone access, crew communication, power-line awareness, lift briefings and refresher training.

Basis: 1926.1424, .1425, .1408(g), .1430 · Role requirements

Module 3 · Crane OperatorRev 2

Operator training, certification and licensing, employer evaluation, trainee limits and retraining.

Basis: 1926.1427, .1430; 1910.179–.180 · Role requirements

Module 4 · Assembly/Disassembly DirectorRev 2

Director qualifications, procedures, crew briefings, pin removal, stability, equipment configuration and rigging.

Basis: 1926.1403–.1406 · Role requirements

Module 5 · Operator EvaluatorRev 2

Evaluator competence, equipment and assigned work, reassignment, documentation and monitoring.

Basis: 1926.1427(b), (f) · Role requirements

Module 6 · Qualified RiggerRev 2

When a qualified rigger is required, inspection, load markings, equipment selection and written and practical evaluation.

Basis: 1926.1401, .1404(r), .1425(c), .251; ASME B30.5, B30.9, B30.26 · Role requirements

Module 7 · Load Handling Equipment UserRev 2

Equipment scope, powered industrial truck training, refresher training, hoists and configuration changes.

Basis: 1910.178(l); 1926.1400(c), .553, .554; ASME B30 · Role requirements

Module 8 · Lift DirectorRev 2

Multiple-crane lift planning, directing the crew, signaling, overlapping crane work and response to plan changes.

Basis: 1926.1432, .1419, .1421; ASME B30.5, P30.1 · Role requirements

Field forms

Blank Word forms for keeping the records OSHA expects and the paperwork clients often ask for (Form 8 also comes as a print-ready PDF). Edit them to fit your program, or print them on a standard letter sheet for sites where tablets and phones are not allowed. Filling in a form does not qualify, certify or train anyone.

Form 1 · Crew Qualification RosterRev 0

One line per person, per role on the job: who is doing what, their qualification basis, expiry, and where the record is kept.

Basis: All roles

Form 2 · Crane Operator Evaluation RecordRev 0

Documents the employer’s evaluation of a crane operator, with the items the record must show. Keep it at the worksite.

Basis: 1926.1427(f)

Form 3 · Signal Person Qualification RecordRev 0

Shows how a signal person was qualified (third-party or employer evaluator) and what they were qualified on.

Basis: 1926.1428

Form 4 · Pre-Lift Meeting and Sign-InRev 0

Who is doing what on the lift, the load, hazards and controls, and a crew sign-in. Repeat when the crew, setup or conditions change.

Basis: ASME P30.1

Form 5 · Crane Shift Inspection ChecklistRev 0

Visual and functional checks a competent person makes each shift, with a defects log. Use alongside the manufacturer’s manual.

Basis: 1926.1412(d)

Form 6 · Rigging Gear Inspection ChecklistRev 0

Before-use inspection log for slings, hardware and below-the-hook devices, with a remove-from-service quick reference.

Basis: 1926.251(a)

Form 7 · Before You Show Up: Records ChecklistRev 0

What to have ready before crane or rigging work starts on a site: the records OSHA requires, and what clients often ask for.

Basis: 29 CFR 1926

Form 8 · Pre-Mobilization Training ChecklistRev 0

One checklist per worker, completed before mobilizing: training, testing, evaluation and records for each assigned role, with OSHA, ASME and state or owner items, a gap log, expiry dates and a release sign-off.

Basis: All roles

Licensed under CC BY 4.0: free to use and adapt, including commercially, with credit to liftrolesreference.org. Keep the notice that the material does not qualify anyone.

About this reference

This site summarizes the minimum US requirements for training, qualifying and evaluating people in crane and rigging roles. It is independent and is not affiliated with, or endorsed by, OSHA, ASME, ANSI, ASSP or any employer, certification body or training provider.

How to use it

  • OSHA law rows come from 29 CFR 1926 (construction) and 1910 (general industry), summarized from osha.gov. Clause numbers link to the regulation text, which controls.
  • Consensus rows come from ANSI/ASME and ANSI/ASSP standards. Those standards are copyrighted, so requirements are paraphrased and cited by clause. Buy the current edition from the publisher before writing them into a procedure.
  • Rows marked Verify were paraphrased from secondary sources or have an approximate clause number.
  • Each role page lists the requirements specific to that role first. Requirements that apply to everyone on the lift are grouped at the bottom of each role page.
  • The Rigging hardware page summarizes inspection types and removal criteria by item. The manufacturer's instructions and the current standard control.
  • Federal OSHA only unless stated. State plans, cities, owners and agencies (for example DOE or USACE sites) may add requirements.

Not legal advice, and not a qualification

This is an informational summary. It does not replace the regulations, the standards, the equipment manufacturer's instructions or advice from a qualified professional. Reading this site or completing a training resource does not qualify, certify or license anyone. Training, evaluation and documentation are the employer's responsibility. Check the edition and effective date of every standard you rely on.

Glossary

Competent person
One who can identify existing and predictable hazards in the work, and who has authorization to take prompt corrective measures to eliminate them. 1926.32(f); 1926.1401
Qualified person
One who, by a recognized degree, certificate or professional standing, or by extensive knowledge, training and experience, has shown the ability to solve problems relating to the subject, work or project. 1926.1401
Qualified rigger
A rigger who meets the criteria for a qualified person. OSHA sets no exam or card; the employer decides and must be able to show the basis. 1926.1401
Fall zone
The area, including the area directly beneath the load, where it is reasonably foreseeable that suspended materials could fall in an accident. 1926.1401
Dedicated spotter (power lines)
A person who meets the signal person qualifications and whose only job is to watch the separation between the power line and the equipment, load line and load. 1926.1401; 1926.1428
Qualified evaluator (third party)
An entity that, because of its independence and expertise, has shown competence in assessing whether people meet the signal person qualification requirements. Its documentation is portable. 1926.1401; 1926.1428(a)(1)
Qualified evaluator (not a third party)
A person employed by the signal person’s employer who has shown competence in that assessment. The qualification is not portable to another employer. 1926.1401; 1926.1428(a)(2)
Standard Method
The protocol for hand signals in Appendix A of Subpart CC. 1926.1401; 1926.1419(c)
Assembly/disassembly (A/D)
Putting up or taking down equipment covered by Subpart CC. For tower cranes, “erecting and climbing” and “dismantling.” 1926.1401; 1926.1404
Operator-in-training
A person not yet certified and evaluated who may operate only under the continuous monitoring of an operator’s trainer, with listed restrictions. 1926.1427(a)(1), (b)
Lift director
The person who directly oversees the lift. OSHA sets a qualification only for multiple-crane lifts; ASME B30.5 treats the role as always filled. Some companies call it the person in charge (PIC) or lift supervisor. 1926.1432(b)(1)
Multiple-lift rigging
In steel erection, hoisting more than one independently rigged structural member at once (“Christmas-treeing”). Workers who do it need specific training. 1926.761(c)(1)
Designated person
In the ASME B30 volumes, a person the employer selects or assigns as competent to do specific duties, such as periodic inspections of slings and rigging hardware. ASME B30 series
Consensus standard
A voluntary standard such as ASME B30 or ANSI/ASSP A10.42. It becomes binding when adopted by contract, owner specification, state rule or company procedure.
Load handling equipment (LHE)
On this site, hoists, jacks, rollers, gantries, winches, below-the-hook devices, forklifts, telehandlers and similar equipment other than cranes. The term follows ASME P30.1.

Use and license

Site text and the awareness modules are licensed under Creative Commons Attribution 4.0 (CC BY 4.0): free to use and adapt, including commercially, with credit to liftrolesreference.org. Regulation text belongs to the public; ASME and ANSI standards belong to their publishers and are only paraphrased here.

Report an error

Spotted a wrong clause, an outdated edition or a missing state rule? Email [email protected] with the page, the row and your source. Corrections are listed under What's changing.

Sources

SourceEditionIssuedStatus as of 15 Nov 2026
OSHA 29 CFR 1926 Subpart CC
Cranes and Derricks in Construction (1926.1400-.1442)
Current eCFR2010; operator rule amended 2018In force. 1427 evaluation/documentation effective 7-Feb-2019.
OSHA 1926.1428
Signal person qualifications
Current2010In force
OSHA 1926.1430
Training
Current2010In force
OSHA 1926.1404
Assembly/Disassembly - general requirements
Current2010In force
OSHA 1926.1401
Definitions
Current2010In force
OSHA 1926.1425
Keeping clear of the load
Current2010In force
OSHA 1910.178
Powered industrial trucks (training at (l))
Current1998 training ruleIn force; applies to construction via 1926.602(d)
ASME B30.5-2025
Mobile and Locomotive Cranes
2025 (rev. of 2021)30-Dec-2025Becomes effective 1 yr after issue (~30-Dec-2026). B30.5-2021 in effect until then. Next edition scheduled 2028.
ASME P30.1-2024
Planning for Load Handling Activities
20247-Feb-2025Current
ASME B30.9-2025
Slings
202518-Jul-2025Current
ASME B30.21-2025
Lever Hoists
202510-Feb-2025Effective 10-Feb-2026
ASME B30 series package
Current editions incl. B30.1-2026, B30.2-2022, B30.3-2025, B30.7-2026, B30.16-2022, B30.20-2025, B30.23-2022, B30.26-2026
VariousVariousCurrent per ANSI webstore
ANSI/ASSP A10.42-2000 (R2017)
Rigging Qualifications and Responsibilities in Construction
2000, reaffirmed 20172017 reaffirmationCurrent
Crane Hot Line, Nov-2024
Proposed B30.5 lift director qualification criteria
ArticleNov-2024Secondary source (lift director qualification criteria)
CEG / CICB / NCCCO articles
B30.5-2021 rigger qualification exam competencies
Articles2021-2023Secondary source (rigger exam competencies)
OSHA 1926.1419
Signals - general requirements
Current2010In force
OSHA 1926.1432
Multiple-crane/derrick lifts
Current2010In force
Washington WSR 25-24-087
WAC 296-155-52902 qualified evaluator (employer) definition
Permanent ruleFiled 2-Dec-2025Effective 2-Jan-2026
NYC DOB lift director registration
Qualifications and application
Web page-Current
OSHA 1926.251
Rigging equipment for material handling
29 CFR-Current
OSHA 1910.184
Slings (general industry)
29 CFR-Current
ASME B30.26
Rigging Hardware
Current editionVerifyCurrent
ASME B30.10
Hooks
Current editionVerifyCurrent
ASME B30.20 / BTH-1
Below-the-Hook Lifting Devices / Design of Below-the-Hook Lifting Devices
Current editionsVerifyCurrent
WSTDA WS-1 / RS-1
Web Sling & Tie Down Association: synthetic web slings / roundslings
Current editionsVerifyCurrent